Recent Posts

Pages: [1] 2 3 ... 10
1
Feature Request / Re: alarm logging
« Last post by jysm1226 on Today at 01:03:04 AM »
Your program is being debugged.
Your program should have any address turned on to trigger an alarm.

This program has to be turned on several times before the alarm rings.
2
Additional Components / Re: NumericUpDown as AHMI control
« Last post by Godra on December 10, 2017, 11:01:06 PM »
There was one bug in the new file so it was updated and replaced.
3
Support Questions / Re: DigitalDisplayPanel Digits color
« Last post by sajidhh on December 10, 2017, 10:46:46 PM »
thanks for your reply i would try it i hope it would work
4
Additional Components / Re: NumericUpDown as AHMI control
« Last post by Godra on December 10, 2017, 06:46:35 PM »
This control was modified and updated, with this new version attached in this post.

 A new property was added, AllowWriteOnly, which is set to True as default.
If you want the control to as well read the current PLC address then change this value.
5
Support Questions / Re: Read/Write floating values in omron plc
« Last post by Lixoudis on December 09, 2017, 11:36:17 AM »
Thanks Archie for the quick response. I will come back if any others bugs will be found. Thanks again
6
Support Questions / Re: Read/Write floating values in omron plc
« Last post by Archie on December 09, 2017, 10:57:45 AM »
There was a conflict with the "," when using controls that used a PCLAddressItem object such as the AnalogValueDisplay. A third patched version has been posted that uses the @ symbol instead of a comma. Example addresses will now be:

D0@F
D0@L

https://sourceforge.net/projects/advancedhmi/files/advancedhmi/3.5

7
Support Questions / Re: Read/Write floating values in omron plc
« Last post by Lixoudis on December 08, 2017, 12:12:41 PM »
Doing some tests its seams that I can read float values in a basic label, I can pass float values through keypad and other means but when I try to read values on analog display through plcaddressvalues I can't use the format D0,F and also i can't read values through datasuscriber event again for the same reason. Is there any way to use it that format in the above controls or not?
8
Support Questions / Re: Read/Write floating values in omron plc
« Last post by Lixoudis on December 08, 2017, 12:16:29 AM »
Thanks for the quick replay I will try the update and come back with feedback
9
Support Questions / Re: Read/Write floating values in omron plc
« Last post by Archie on December 07, 2017, 08:38:08 PM »
There is a beta patch for 3.99x that adds this feature to the Omron FINS driver. It works by using address modifiers. For example:

D0,F   will read a floating point
D0,L   will read a long 32 bit integer

You can download the V3.99xPatched2 file from here:

https://sourceforge.net/projects/advancedhmi/files/advancedhmi/3.5

10
Support Questions / Read/Write floating values in omron plc
« Last post by Lixoudis on December 07, 2017, 12:09:14 PM »
Hello guys I have a question regarding the omron fins serial driver. Am using a CP1L Plc and I try to read or write float numbers to Plc with no luck. Is it possible to do it or not? For the reading part I have succeeded to read them by convert the real number to int inside the ladder and then just putting on the analog display value a scale factor but for the write I haven't found any way to do it. I await your suggestions
Pages: [1] 2 3 ... 10