Messages

1

Support Questions / Re: Advanced HMI with Solo Pid Controller from automation direct

« on: May 21, 2016, 08:57:05 PM »

oh btw this worked perfectly. thanks for the help

2

Support Questions / Re: basic trend chart not graphing

« on: May 21, 2016, 04:33:57 PM »

ok that's the problem... its showing 777 which is 77.7.......anyway to add a decimal to the trend chart?

3

Support Questions / Re: basic trend chart not graphing

« on: May 21, 2016, 04:22:15 PM »

my range normally is 60-220

starting temp is 70 so it should show up.

4

Support Questions / basic trend chart not graphing

« on: May 21, 2016, 04:12:52 PM »

I am trying to get the basic trend chart to graph the temperature change on my solo temp controller...... I have it set up properly with the addresses needed and high and low is also set properly within temp range but the trend chart doesn't graph anything at all....even if I download the advanced hmi/solo project and run it nothing is graphed..everything else works but the graph

5

Support Questions / Re: advanced hmi doesn't run ones built

« on: May 21, 2016, 03:58:57 PM »

my bad archie....... I navigated to the wrong output folder sorry

6

Support Questions / Re: advanced hmi doesn't run ones built

« on: May 21, 2016, 03:50:10 PM »

doesn't open it either way........ ive even tried copying it to a diff computer...still doesn't....... i'm running windows 10 64 bit

7

Support Questions / Re: advanced hmi doesn't run ones built

« on: May 21, 2016, 03:16:21 PM »

to build the project all I have to do is switch to release and click build advanced hmi right?

8

Support Questions / Re: advanced hmi doesn't run ones built

« on: May 21, 2016, 03:15:47 PM »

nope it does not....

9

Support Questions / Re: advanced hmi doesn't run ones built

« on: May 21, 2016, 03:02:21 PM »

can't see anything......and even after a restart it just doesn't open

10

Support Questions / advanced hmi doesn't run ones built

« on: May 21, 2016, 02:00:16 PM »

I am having issues with my advanced hmi buids.......my advanced hmi project works great when I run in it visual studios but when I switch to release and click build advanced hmi and then go into the release folder and try running the exe file nothing opens up.......what could cause this issue? thanks

11

Support Questions / Re: more than one page

« on: May 19, 2016, 05:37:34 PM »

simple enough thanks

12

Support Questions / more than one page

« on: May 19, 2016, 04:57:09 PM »

I for the life of me can't figure out how to have more than one page with advanced hmi.... Like one page for conrols another for alarms and so on.......and how to cycle from one to the other? thanks

13

Support Questions / Re: Advanced HMI with Solo Pid Controller from automation direct

« on: May 14, 2016, 02:35:11 PM »

that worked perfect thanks .... but now I have another question......
my pid has a couple different control modes but the two i'm interested in using are
PID control
Manual control

lets say the Modbus address for control mode is 40098. Each control mode is assigned a number and that is what you enter into temp controller to choose your control mode

so lets say Manual control is "0"
Pid control is "2"

how would I be able write one of those two numbers to pid using a selector switch? thanks

14

Support Questions / Re: Advanced HMI with Solo Pid Controller from automation direct

« on: May 13, 2016, 08:20:54 PM »

any idea about the 2049 Modbus addresses? thanks for the help btw

15

Support Questions / Re: Advanced HMI with Solo Pid Controller from automation direct

« on: May 13, 2016, 06:33:20 PM »

I set the maximum on the slider to 1000 which shows the maximum on the slider as 1000

I used  vertical slider 1 because I like that It shows the value