1
Support Questions / Invert bit
« on: June 26, 2017, 03:38:15 PM »
How can i reverse the reading on: visible PLC address.
True when the specified bit is = 0? Rather than = 1
True when the specified bit is = 0? Rather than = 1
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Support Questions / Re: Windows CE 7
« on: June 16, 2017, 02:48:46 AM »
Could only run the finished executable?
Place in .. AdvancedHMI /bin/ debug/AdvancedHMI.exe
Place in .. AdvancedHMI /bin/ debug/AdvancedHMI.exe
3
Support Questions / Raspberry PI error
« on: May 31, 2017, 12:39:16 PM »
I'm trying to start AHMI on the raspberryPI3 but I always get this error as soon as I close the application that does not communicate:
System.IO.IOException: Descrittore di file errato
at System.IO.Ports.SerialPortStream.ThrowIOException () [0x00000] in <filename unknown>:0
at System.IO.Ports.SerialPortStream.Dispose (Boolean disposing) [0x00000] in <filename unknown>:0
at System.IO.Ports.SerialPortStream.Finalize () [0x00000] in <filename unknown>:0
I'm connected via usb-serial adapter and tried to set it on PORTNAME com1, com2, usb1 but I get the same error result from the raspberry
System.IO.IOException: Descrittore di file errato
at System.IO.Ports.SerialPortStream.ThrowIOException () [0x00000] in <filename unknown>:0
at System.IO.Ports.SerialPortStream.Dispose (Boolean disposing) [0x00000] in <filename unknown>:0
at System.IO.Ports.SerialPortStream.Finalize () [0x00000] in <filename unknown>:0
I'm connected via usb-serial adapter and tried to set it on PORTNAME com1, com2, usb1 but I get the same error result from the raspberry
4
Open Discussion / Re: Solution for Pi + mono AAHMI + ML1000 ??
« on: May 17, 2017, 02:45:37 AM »
Are there any news on this topic?
5
Support Questions / Raspberry & serial conn Definitive solution?
« on: May 16, 2017, 06:07:50 AM »
I read many arguments in this forum about connecting via USB port.
Has it refused to come to a definitive working solution?
For a connection between serial port PLC and Raspberry Pi
Has it refused to come to a definitive working solution?
For a connection between serial port PLC and Raspberry Pi
6
Support Questions / Re: Omron & serial FINS
« on: May 15, 2017, 07:29:48 PM »
Wowow, RESOLVED.
I found a service that occupied the com, an old SCADA software installed for trial.
I'm already reading the data on the Voltmeters.
Thanks for the support
I found a service that occupied the com, an old SCADA software installed for trial.
I'm already reading the data on the Voltmeters.
Thanks for the support
7
Support Questions / Re: Omron & serial FINS
« on: May 15, 2017, 07:19:18 PM »
I do not have other PCs with native serial port,
If I buy a usb-serial adapter to work?
It's strange this signal coming out of the com1 without any software started.
Or is it caused by jumpers 7-8 or 4-6 on com1?
On the AHMI panel I can set COM 12, the driver works for com ports?
If I buy a usb-serial adapter to work?
It's strange this signal coming out of the com1 without any software started.
Or is it caused by jumpers 7-8 or 4-6 on com1?
On the AHMI panel I can set COM 12, the driver works for com ports?
8
Support Questions / Re: Omron & serial FINS
« on: May 15, 2017, 07:10:46 PM »
I still have no connection.
But as soon as I turn on the PC without starting any program I see the communication led, 1 flash per second, on the plc flash.
Connected osilloscope, I saw a signal coming from PC from com1
But as soon as I turn on the PC without starting any program I see the communication led, 1 flash per second, on the plc flash.
Connected osilloscope, I saw a signal coming from PC from com1
9
Support Questions / Re: Omron & serial FINS
« on: May 15, 2017, 06:47:42 PM »
I'm connected directli with a serial cable between plc and pc, with this configuration:
PC side PLC side
2----------------------2
3----------------------3
7--- ---4
I I
8--- ---5
5----------------------9
PC side PLC side
2----------------------2
3----------------------3
7--- ---4
I I
8--- ---5
5----------------------9
10
Support Questions / Re: Omron & serial FINS
« on: May 15, 2017, 03:05:47 PM »
Ok thanks, i start to try but i am with serial connection.
I think it should not change much.
Regarding the network and node to set up?
I think it should not change much.
Regarding the network and node to set up?
11
Support Questions / Re: Omron & serial FINS
« on: May 15, 2017, 02:25:18 PM »
Are you sure ? You have experience of non omron serial FINS, from what I read in the manual you need to have send and receive commands
12
Support Questions / Re: Omron & serial FINS
« on: May 15, 2017, 01:44:53 PM »
I send words from plc to visualize them on AHMI as the voltmeter.
This to start checking out communication, after being sure of this I will start developing my project
This to start checking out communication, after being sure of this I will start developing my project
13
Support Questions / Re: Omron & serial FINS
« on: May 15, 2017, 12:31:10 PM »
Like the 3.99
How do i set TreadDataAsHEX ?
end the Target Network Address , node address , unit address on comunication setting Omron Serial FINS Are the addresses that AHMI uses to answer or read?
With the PLC I transmit to Network destination 1 Node 2 and Unit 0
How do i set TreadDataAsHEX ?
end the Target Network Address , node address , unit address on comunication setting Omron Serial FINS Are the addresses that AHMI uses to answer or read?
With the PLC I transmit to Network destination 1 Node 2 and Unit 0
14
Support Questions / Re: Omron & serial FINS
« on: May 14, 2017, 02:35:45 AM »
Thanks for the reply, I read this http://advancedhmi.com/forum/index.php?topic=959.msg5000#msg5000
Do I have to make the same fix or have the driver been fixed?
Do I have to make the same fix or have the driver been fixed?
15
Support Questions / Omron & serial FINS
« on: May 12, 2017, 12:42:29 PM »
Hello to all
I'm trying to connect to the Omron CJ1M PLC by serial with FINS commands.
From the PLC sending 10 channels D0100 to D0109 all with "FFFF"
On HMI I set OmronSerialFINSCom1 driver on com1 115200,7, E, 2 (same on plc) or tried also 9600,7,E, 2.
In digitalPanelMetr objects I set to PLCAddressValue D100 or 100 or 1
But I do not receive anything.
What value should I set in this field?
The com1 serial is active and verified with port sniffer
Thank you
I'm trying to connect to the Omron CJ1M PLC by serial with FINS commands.
From the PLC sending 10 channels D0100 to D0109 all with "FFFF"
On HMI I set OmronSerialFINSCom1 driver on com1 115200,7, E, 2 (same on plc) or tried also 9600,7,E, 2.
In digitalPanelMetr objects I set to PLCAddressValue D100 or 100 or 1
But I do not receive anything.
What value should I set in this field?
The com1 serial is active and verified with port sniffer
Thank you
Pages: [1]