Messages

1

Open Discussion / Re: Errors in Advanced HMI

« on: May 19, 2018, 01:30:42 AM »

My problem regarding modbus communication is being solved and I need to run my display for various application and for that I need to create a another HMI screen.

But I could not open a new ,how to open a new advanced HMI screen .

And also how to display a 32 bit signed integer values in my display.

2

Open Discussion / Re: Errors in Advanced HMI

« on: May 18, 2018, 06:38:47 AM »

It was working properly. How to open a another file in existing project.

Since i need to connect another microcontroller for another application.Now I cannot open another file in it.

3

Open Discussion / Re: Errors in Advanced HMI

« on: May 18, 2018, 12:59:10 AM »

Thank You ...and I am getting a delay of 3 to 5 sec to fetch a data why is it so? all the parameters are being set correctly.

4

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 11:57:16 PM »

This is my port settings.

5

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 05:18:40 AM »

Whenever I changed my pollrate value the data is not being displayed in my window but the driver log receives and sends the data.

And when I change my pollrate value the communication takes place but another error window appears as arithmetic operation stack overflow.

Please find me a solution to this problem.

I had attached my both driver log data and my error display.

6

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 03:36:57 AM »

Ok I will check with that, what should be the timeout value to maintain.

7

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 03:18:20 AM »

Yes , but whenever I changed my pollride more than 100 or to 500 My HMI is running but I cannot receive any data from my controller and I change that to 80 the response is immediate and it works properly.

FYI the driver log is attached below

8

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 02:55:08 AM »

FYI This is my driver log file.

9

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 02:41:29 AM »

Now I am getting the disassembly error.

source code missing what should I do to rectify this.

10

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 02:32:16 AM »

When I am running I had now noticed other error window now. I had attached the screen shot below.

The break window now is replaced by this window.

11

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 02:16:53 AM »

Yes i am using RS 232 adaptor.

12

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 02:12:34 AM »

An unhandled exception of type 'System.ArgumentException' occurred in mscorlib.dll
Offset and length were out of bounds for the array or count is greater than the number of elements from index to the end of the source collection.

The program '[9504] AdvancedHMI.exe' has exited with code -1 (0xffffffff).


This was coming in my output window.

13

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 01:57:37 AM »

It comes out from the running state and I need to restart it again.So My data's are being fetched with dime delay.

It is happening for every 50sec to 1 minute when ever I start my execution.

14

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 12:32:43 AM »

This is my mainform settings.I had not used any other drivers in my USB port. What ever I had been modified It would not affect my real time display of my front screen.
Where my basic objective is to display my analog values.

15

Open Discussion / Re: Errors in Advanced HMI

« on: May 17, 2018, 12:16:03 AM »

Sir/Madam

This is my front screen where I had used only digital panel label to display my parameters. But when I am running the screen is being moved to break mode here by I had attached  my modbus property screenshot.

How to overcome this problem.