« previous next »
Pages: 1 2 [3]

Author Topic: SLC 5/02  (Read 8396 times)

tylerinthetub

  • Newbie
  • *
  • Posts: 24
    • View Profile
Re: SLC 5/02
« Reply #30 on: April 22, 2017, 10:38:18 AM »
Did a little more reading and digging and the PLC is for sure on Node 1, Node 0 is Rs linx

Also ungraded to 3.99w

Still no luck though, will keep digging today.
Logged

Archie

  • Administrator
  • Hero Member
  • *****
  • Posts: 5322
    • View Profile
    • AdvancedHMI
Re: SLC 5/02
« Reply #31 on: April 22, 2017, 11:07:28 AM »
Do you have MyNode set to 0 and TargetNode set to 1 in the SerialDF1 driver?
Logged

Archie

  • Administrator
  • Hero Member
  • *****
  • Posts: 5322
    • View Profile
    • AdvancedHMI
Re: SLC 5/02
« Reply #32 on: April 22, 2017, 11:15:48 AM »
I think the 5/02 uses a smaller PCC packet size, so try reducing MaxPCCCPacket size to 80
Logged

tylerinthetub

  • Newbie
  • *
  • Posts: 24
    • View Profile
Re: SLC 5/02
« Reply #33 on: April 22, 2017, 01:04:04 PM »
Yup my node set to 0 and target node set to 1, lowest packet size I can set is 92. Still no luck, I'm going to try reinstalling the driver
Logged

Archie

  • Administrator
  • Hero Member
  • *****
  • Posts: 5322
    • View Profile
    • AdvancedHMI
Re: SLC 5/02
« Reply #34 on: April 22, 2017, 01:19:01 PM »
When you ran Device Monitoring Studio, it showed only a connection, but no transmission of data. Add a BasicLabel to the form and set PLCAddressValue to N7:0, then run that capture again.
Logged

tylerinthetub

  • Newbie
  • *
  • Posts: 24
    • View Profile
Re: SLC 5/02
« Reply #35 on: April 22, 2017, 01:31:23 PM »
Woohoo its talking!
Logged

tylerinthetub

  • Newbie
  • *
  • Posts: 24
    • View Profile
Re: SLC 5/02
« Reply #36 on: April 22, 2017, 01:36:51 PM »
Ok I have coms back and forth now, thank you guys so much. I will screen cap and post all my final settings and append the thread title so if anyone else comes looking the info will be here.
Logged

Archie

  • Administrator
  • Hero Member
  • *****
  • Posts: 5322
    • View Profile
    • AdvancedHMI
Re: SLC 5/02
« Reply #37 on: April 22, 2017, 02:11:48 PM »
I was just about to go to the office to dig in the "Deep Storage" because I remembered a KF3 box and a 5/02 being there. Glad you got it working before I had to dig in that area.
Logged

tylerinthetub

  • Newbie
  • *
  • Posts: 24
    • View Profile
Re: SLC 5/02
« Reply #38 on: April 22, 2017, 03:44:03 PM »
Ok final settings:

Logged

bachphi

  • Hero Member
  • *****
  • Posts: 671
    • View Profile
Re: SLC 5/02
« Reply #39 on: April 23, 2017, 10:01:37 AM »
I am glad it's working out for you, atleast I dont have to test it out. Was the packet size the key here?

Looks like your plumbing skill is better than wiring skill :=) . I did have a really good offer from the very same company that was in the picture. They told me, at the time, that I would get a monthly "stipend" in the form 24 can of beers , i think. hehe. I turned them for family reason.




Logged
===================================================
This is NOT alt.read.my.mind.
No such thing is sh^t-for-brains unless you are posting to alt.read.my.mind.
===================================================

tylerinthetub

  • Newbie
  • *
  • Posts: 24
    • View Profile
Re: SLC 5/02
« Reply #40 on: April 23, 2017, 10:04:19 PM »
Quote from: bachphi on April 23, 2017, 10:01:37 AM
I am glad it's working out for you, atleast I dont have to test it out. Was the packet size the key here?

Looks like your plumbing skill is better than wiring skill :=) . I did have a really good offer from the very same company that was in the picture. They told me, at the time, that I would get a monthly "stipend" in the form 24 can of beers , i think. hehe. I turned them for family reason.

The driver re-install was what eventually did the trick, but I don't really have much of a desire to work backwards and figure out where it stops working.

I put about 15 hrs of programming in this weekend, when I finish the wiring up and it works I'll put a thread up I the projects section.
Logged
Pages: 1 2 [3]
« previous next »